異形切齒刀的成形工藝與磨削工藝 

異形切齒刀的成形工藝與磨削工藝

異形切齒刀的成形工藝與磨削工藝：幾年前曾有專家曾預言今后的齒刀在齒輪加工方面的應用將大為減少,到那時,將沒有汽車齒輪生產企業再使用齒刀,在設計制造齒輪傳動裝置時,也不再采用插齒工藝加工齒輪。
A few years ago had experts predicted that the future of cutter used in gear processing will be greatly reduced, then, there will be no automobile gear manufacturing enterprises, and then use the knife tooth, in the design and manufacture of gear transmission device, also no longer used in gear processing gear.
一般認為插齒工藝是在齒輪不能用滾刀加工的情況下采用的齒輪加工方法,這種加工方法費用高、齒輪質量差。事實上插齒是為帶臺肩的齒輪進行齒形加工而采用的除此之外,插齒刀也廣泛用于是直齒斜齒的內齒輪加工如果齒輪采用內齒拉削工藝比較困難就需要采用插齒刀加工。
It is generally believed that the gear shaping process is a gear processing method which is used in the case that the gear can not be processed by the hob. In fact in tooth is with a shoulder gear of tooth shape processing and the use of in addition, in cutter is widely used in is straight tooth bevel gear processing if gear adopts the inner tooth pull cutting process is difficult to need the shaper cutters processing.
插齒加工的缺點在于,與滾齒相比其加工的循環時間較長。另外齒刀在加工齒輪時由于兩者嚙合運動,齒刀的整體誤差插齒刀刀齒上可能出現的誤差或變形(如裂紋、刀齒磨損及刀齒的損壞)會傳遞到加齒輪的輪齒被破壞是不能使用的。還有許多還沒完全執行的方案可使滾刀和插齒刀在技術上的差距進一步縮短。這關系到通過生產齒輪刀具的新型機器。即使不能充分利用齒輪刀具而且重磨次數有限制,這些機器也有利于降低生產費用。磨削插齒刀時難以讓根圓直徑Di和齒頂倒角高度Sm保持一致。這是因為重磨后插齒刀與齒輪的軸距及插齒刀齒厚這兩參數的減少,不可能同插刀本身的齒頂倒角高度及在有齒頂倒角部位上的斜度取得一致。數學模型包含著讓軸距變化與插齒刀高度H不相稱的三角方程。相反,齒頂修形St和齒頂倒角的斜度以直線關系對應。二者根據插齒刀高度的減少遵照線性關系公式而變。

申瑞將以卓越的品質、優惠的價格、優質的服務。歡迎廣大新老客戶與我們聯系，洽談合作。

The disadvantage of gear shaping is that the cycle time is longer than that of the gear teeth. Also in cutter teeth in the gear processing due to their engagement, cutter tooth of the overall error in error may occur on the gear hob tooth or deformation, such as crack, the cutter tooth wear and the cutter tooth damage will transfer to the gear tooth is cannot be used. There are a number of programs that are not fully implemented to make the gap between the hob and the pinion cutter further reduced. This is related to the production of gear cutting tool by a new type of machine. These machines are also beneficial to reduce production costs, even if they are unable to make full use of the gear cutting tool and the number of heavy grinding is limited. It is difficult to make the grinding cutter root diameter Di and height Sm consistent tooth crest chamfering. This is because the grinding in the wheelbase of cutter and gear and gear shaper cutter tooth thick the two parameters of the reduced, it is impossible teeth in the knife itself top chamfer height and the addendum chamfer on the part of the slope of the agreement. The mathematical model contains a triangular equation that is not commensurate with the height of the H cutter. On the contrary, the tooth tip modification St and chamfering tooth inclination to linear relation. According to the reduction of the height of the gear slotting cutter, the two changes according to the formula of linear relation.
達到上述目標的必要條件在于通過平移砂輪而得到想要的齒刀。這類砂輪除了在刀具雙齒面上開展漸開線運動,還開展使齒頂倒角斜度線性的軸向運動。
The necessary condition to achieve the above objective is to get the desired tooth knife through the translation grinding wheel. This kind of grinding wheel is carried out in addition to involute motion in the tool on the tooth surface of double axial movement, also carried out the tooth crest chamfering angle linear.